Search  
OUR PRODUCTS
Lab Ovens & Equipments
Tubular Heaters
Finned Strip Heaters
Duct Heaters
Circulation Heaters
Ceramic Band Heaters
Industrial Ovens
Load Banks
Suction Heaters
Drum Heaters
Cartridge Heaters
Process Immersion Heaters
Band Heaters
Temparature Sensors
Casted Heaters
U.V Weathering Tester
Mica Strip & Plate Heaters
Ceramic Heating Elements
High Density Catridge Heaters
Climatic Chambers
 
 
:: Suction Heaters / Out Flow Heaters ::
 
MATRUSREE Suction Heater is a flow-through electrical heater, ideal for heating of oil or water. Its heat load capacities range from 3 to 200 kW, with design conditions up to 16 bar and 160C. They are generally Mounted Horizontally, but is also available as Vertical Mounting with Different MOC. These heaters are designed specially as Suction Heaters but can also be designed for Out Flow Heaters as well as Immersion Heaters Application.

Heating of viscous materials, in large storage tanks, to pumping temperatures. Maintaining an entire tank of viscous fluids such as fuel oil or asphalt at pumping temperatures is very costly. In many applications it is not practical or economical because the tanks are located underground or are not insulated. Type MATRUSREE Suction Oil Heaters are a cost-effective solution to this problem. Suction heaters are specifically designed to heat only that amount of material that is to be pumped from a large storage tank. The outlet nozzle is attached to the pump suction. The heater heats the material inside the heater pipe body which is then drawn through the heater into the suction side of the pump. This technique saves substantial energy costs since it is not necessary to heat the entire contents of the tank to draw off relatively small amounts of viscous materials. Complete weather-proof construction makes these heaters perfect for installation in large outdoor storage tanks. Large \heater inlet provides smooth, full-flow through the heater.
FEATURES
Terminal Enclosure:
MATRUSREE CIRCULATIUON HEATERS circulation heaters are designed to be installed outdoors in exposed areas. Enclosures are designed to be Moisture Resistant or Moisture and Explosion Resistant. Low Watt Density Elements make the heaters safe to use on most viscous liquids. Carbonization is minimized.

Vessel: carbon steel pipe. Heater and mounting flanges are ANSI B16.5 150 Lb carbon steel. AssemblyProvided with thermal insulation & outer Metal Sheath Covering

Thermostats/ Temperature Controls and Control Panels:: MATRUSREE Suction Heaters Are provided with temperature controls to control fluid outlet temperatures and limit internal temperatures under abnormal Depending on customer specifications, MATRUSREE Suction Heaters may be supplied with factory equipped AR thermostats / Temperature sensors in case of Digital Temperature controllers other Panel Accessories. Integral or remote mounted control panels with electronic controls and solid state (SSR) or contactor power controllers can be provided using virtually any combination of control devices.
TECHNICAL DETAILS OF ELECTRIC HEATERS:
Element design Element consists of open helical coils of high Resistance Nichrome (80/20) wire carried through ceramic bobbins. All Corderite bobbins are tied in position with a SS-304 centre rod.

These elements are fitted inside solid drawn tube of size 40 NB schedule 40. On installation over Flange, Elements are fixed using Z-clamp for ease of replacement. Renewable cartridges facilitate easy replacement of elements without emptying the tanks.
Watt Density Watt density is the heating density experienced by oil over the outside area of encasing metallic pipe. Offered range is 1.5 to 2.0 watts per square cm.
Power supply & control Heaters upto 3Kw are designed to operate on 230V, single phase AC Supply. From 6 Kw onwards, these operate on 415V, 3 phase AC Supply. All heaters are provided with a thermostat for precise temperature control. Heaters above 12Kw are provided with standby thermostat.
Copyright© All rights reserved | Matrusree Electro Heats | Privacy Policy